Secondary throat actuation Diaphragm- CLOSED

[timpa136]

Here is another group buy, Let me know of interest as the quantity order will determine price.

May 9, 2017 at 2:04pm


Post by timpa136 on May 9, 2017 at 2:04pm

    I have the ability to arrange a group Secondary diaphragm rebuilding. Your old diaphragm will be media blasted and clear coated.

I'm looking at under $40.00 USD depending on quantity, possibly slightly more now, the price estimates were from last year.

I can't completely guarantee you will get your own back but extremely polished or shiny ones from owners will be noted and vice versa.

   EDIT: I will label each owners unit stem with a wire tag  .

They would be mailed to me, I will get our groups total cores to the re manufacturer and I will mail  back to you individually. I am addressing interest

only at this point . Previous rebuilds done years ago were as good in functioning as the original . I have contacted the same

remanufacturer as before for this offer.

EDIT:

Testing is straightforward without a vacuum pump. If you do not have a twist assist or throttle lock, you will need the help of your assistant.

Hold throttle wide full open

Slip off vacuum hose

reach under and lift to open the secondary throttle

place finger over vacuum hose and confirm it holds vacuum

[h2e Al In Aus]

Hi Tim
Im in For 2. urs al in Aus

[re5norway]

Hi Tim
I am also interested, please set me up for 2 units.

[timpa136]

Both requests are noted. As a method of planning, I expect to round up requests and acquire a firm estimate towards the end of this July.

[wayne]

Hi Tim, please count me in for one as well.

[timpa136]

Apr 22, 2018 14:14:51 GMT -5 timpa136 said:

Both requests are noted. As a method of planning, I expect to round up requests and acquire a firm estimate towards the end of this July.

    On to plan B.

    I wanted to double check arrangements at the original rebuilder and they can no longer rebuild ours. Interesting though his long time employee

remembered them . They did offer a referral to one other rebuilder that they work with so I will contact them.

Tim

[timpa136]

Jul 31, 2018 17:14:27 GMT -5 timpa136 said:

Apr 22, 2018 14:14:51 GMT -5 timpa136 said:

Both requests are noted. As a method of planning, I expect to round up requests and acquire a firm estimate towards the end of this July.

           On to plan B.

    I wanted to double check arrangements at the original rebuilder and they can no longer rebuild ours. Interesting though his long time

    employee remembered them . They did offer a referral to one other rebuilder that they work with so I will contact them.

Tim

        This is very encouraging. I suggest members check out your units to determine weather you will be interested or not. 

         I am looking into getting them plated with the new referral!   More later.

     Tim  08/04/2018

[timpa136]

I need to know of any of your questions to address. Please review the initial post, the extra benefit now is they will be plated and I really

want to and expect to hold the price but I need firm commitments as quanity affects the price.

When I have enough firm orders, I will  ask you to mail the diaphragms to me post haste.  I'm looking to making a decision  08/17/2018.

Tim

[Jess]

Tim,

put me down for 5

best,

[re5norway]

Tim,

I have 2 units to rebuild

Gunnar

[timpa136]

Following up and to add a bit of assurance to you forum members, read, my own, I am going to send in my core and get a sample made.

I have every ones interests noted . Allow 2 weeks to determine they have everything as it is" not too common" they tell me. That surprises me

Thanks

Tim

[hudson]

I have two that I would like to have done. My concerns are the plastic bushing at the end of the rod,(Some are more worn than others) rotation timing of 3 mounting holes vs the hole in rod and hose nipple. If you decide to go ahead please e-mail me with address and how to pay. [e-mail]

[timpa136]

    Brian, as far as I know, they cannot replace the plastic bushing. I have been supplied a small Jesus snap pin that should hold for you.

I agree on the alignment, I have addressed those concerns as well. My sample is currently at the rebuilder as those were my concerns as well.

Should know soon.

Tim

    EDIT: All have been notified and PIC sent. If I missed you Please PM me right away. Thanks 09/26/18

    EDIT: Got my samples in hand this evening and  they look and vacuum test just as good as they are pictured. I will put my rebuilt diaphragm  on my

driver tomorrow and expect to call in your cores right away so get ready as I will need to send in one complete shipment post haste.

    Al, I am unable to contact you, please get in touch. Thanks 09/28/18

[timpa136]

Aug 22, 2018 15:06:21 GMT -5 timpa136 said:

    EDIT: All have been notified and picture/illustrations sent. If I missed you Please PM me right away. Thanks 09/26/18

    EDIT: Got my samples in hand this evening and  they look and vacuum test just as good as pictured. I will put my rebuilt diaphragm  on my

driver tomorrow and expect to call in your cores right away so get ready as I will need to send in one complete shipment post haste.

    Al, I am unable to contact you, please get in touch. Thanks 09/28/18

      To All,

    The diaphragms function and test and look great. 

    PM me for my address.  Offered are  3 choices of finish, let me know your preference.

    Media blasted and clear coated.

    Silver appearing zinc.  (I estimate most will choose this finish.) 

    Yellow appearing zinc finish.

                            Please email me , or PM me for my address and mailing instructions.  I will mark and tag your stems for identification. 

                                         Thanks -  Your prompt response is expressly appreciated as they have the tooling on hold for us now.

[timpa136]

    To All,

The diaphragms function and test and look great.

PM me for my address. Offered are 3 choices of finish, let me know your preference.

    Media blasted and clear coated.

    Silver appearing zinc. (I estimate most will choose this finish.)

    Yellow appearing zinc finish.

Please email me , or PM me for my address and mailing instructions. I will mark and tag your stems for identification.

Thanks - Your prompt response is expressly appreciated as they have the tooling on hold for us now.